武汉莫诺螺杆泵配件诚信企业「螺耐斯」[螺耐斯10e361c]内容： 管柱脱落是自由式管柱结构经常发生的一种现象，这是由于正常运转时转子旋转对定子产生的摩擦扭矩方向实际上是定子及油管的连接螺纹的卸扣方向，如果摩擦力矩大于油管扣的上扣扭矩，油管就脱扣。当尾管很重时，还会出现螺纹掳扣。当管柱脱落时，通过作业重新连接好就能恢复生产。如果未发生螺纹掳扣，可以采取对扣方式打捞，如果发生掳扣，必须下打捞工具进行打捞。Column shedding is a common phenomenon of free tube structure, which is due to the direction of rotation of the friction torque generated by the stator rotor during normal operation is actually a stator and tubing connection1 screw shackle direction, if the friction torque is greater than the pipe le on torque, oil pipe tripping. When the tail pipe is very heavy, there will also be a thread caption. When the pipe column falls off, the production can be restored by reconnecting the work. If the le is not threaded, it can be salvaged by the way of the le. If the le occurs, the fishing tool must be salvaged.
Ｅ、抽油杆扶正器E, sucker rod centralizer抽油杆扶正器由心轴和扶正筒组成，它接在两根抽油杆之间，被卡在两个抽油杆接箍之间。心轴也就是一要极短的抽油杆短节。扶正筒是一个内孔比心轴大１ＭＭ左右的空心塑料筒，外部有四个略比油管内径小的扶正翼，采取浇注成型。扶正筒可以围绕心轴转动，防止抽油杆旋转时与内壁接触而磨蚀油管，又可以让流体通过。The sucker rod centralizer is comed of the heart shaft and the upright cylinder, which is connected between the two sucker rods and is stuck between the two sucker rod hoops. The axis of the heart is also an extremely short rod short section. The centering cylinder is a hollow plastic tube inner hole Bixin shaft around 1MM, external four slightly smaller than the diameter of the tubing centralizer wing, adopt casting. The centralizer can revolve around the axis to prevent the sucker rod from touching the inner wall when it rotates, and it can also let the fluid pass through.
211G型单螺杆泵可无脉动地工作 G型单螺杆泵工作时,通过螺杆转子与泵套的孔壁间形成的一个个密封腔,平稳地从低压区运送到高压区,在整个运送过程中,介质作纯轴向运动,可完全做到无脉动地运送介质。这一点与齿轮泵不同。齿轮泵工作时,在齿轮的转动下,介质作轴向与径向及其复合方向的运动,产生明显的搅拌现象。其输出压力的表现形式:G型单螺杆泵的输出压力比较稳定,齿轮泵则出口压力会有波动。这一点在输送高粘度的介质(如重油等)时比较突出。
以上信息由专业从事莫诺螺杆泵配件的螺耐斯于2024/5/15 13:04:16发布
转载请注明来源：http://m.herostart.com/qynews/lnshbsb-2753198518.html
上一条：宁夏手动弯道器生产来电洽谈「多图」
下一条：大同高压二氧化碳钢瓶检测服务介绍「成安消防设备」
